We've noticed the article pertaining to Installing A Bathtub down the page on the net and reckoned it made perfect sense to relate it with you on this page.
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old tub with a new one is additionally a reasonably hard job. If the old bathtub is conveniently obtainable, the job can relocate speedily; if you need to open a wall surface to get rid of the old bathtub and position the new bathtub, the task is much harder. In either situation, the project is within a home handyman's skills, although you will certainly need a helper to move out the old bathtub as well as embeded in the new one. Make certain you have certified on your own for the work and also are comfortable trying it. Instead of employing a service provider to take control of a halfway-completed job, it is much better to take into consideration utilizing one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This short article will certainly help you set up a new tub in your restroom if you have actually currently bought a new tub and also do not need to transform the arrangement of your previous supply of water pipelines.
Your devices as well as product checklist must consist of the following:
- New Bath tub
- Hammer
- Pipe Wrenches
- Prybar
- Safety Glasses
- Level
- Pliers
- Adjustable Wrench
- Putty Blade
- Screwdriver
- Cold Chisel
- Tape Measure
- Pipe Caps
Planning for the Setup
Firstly, the supporting structure supplied with the bathroom should be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you use all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing faucets can be rather problematic because of the limited access that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning during this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, place the bath tub in the required setting. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the bath tub until the spirit level reviews level.
To set up taps, fit all-time low of the outermost adaptable faucet port to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water supply and also examine all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bathtub and also examine the overflow outlet and also the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's user's manual. Tiling as well as securing around the tub should wait up until the tub has actually been used a minimum of when as this will settle it into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existing supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in area in between the tap and also the sink. Safeguard the faucet in place with the maker given backnut. Once the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular tap adapters. The previous kind needs to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a rigid seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in issues with wetness and possible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the tub with water before securing, to enable the motion experienced when the tub remains in use. The sealant can crack relatively very early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly available on the market. It is a good idea to fit the ceramic tiles using waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was guided to that article on How to Install a Bathtub from a good friend on another website. So long as you liked our blog post plz remember to pass it around. We value reading our article about Installing A Bathtub.
Request An Estimate
Comments on “Getting Familiar with Plumbing: Before Installing a Bathtub”